WTB autococker parts for full build

[flavordeliverer]

I need to build something! I miss cockers and want one again but I also want to make it as difficult as possible to get to that point. I don’t have any expectations or end goal in mind.

I have about a 15 year gap in paintball knowledge but I’m assuming autococker tech hasn’t changed exponentially. I’d like to buy cheaper priced parts (all used is my assumption). If you have anything parts that have been laying around for a while or want to clear out, here’s your chance!

I’ll list what parts I’ve acquired in this post as I get them. So if you have anything, offer away! I literally have nothing; no tubing, no HPA tanks, etc.

also, I’m happy to trade any Hawaiiana stuff as well. Since I’m here, let me know if you want anything shipped.

Looking for:

-body with back block, vasa
-front block
-feedneck
-pneumatics: ram, lpr, 3way
-timing rod
-pump arm
-bolt and pin
-high pressure regulator
-frame (slider)
-asa
-macro line fittings
-mini hose for pnues
-lower tube: hammer with lug, spring
-IVG
-valve
-cocking rod
-barrel
-grips/panels

[superman]

There have been some nice changes to make things more user friendly. Shocktech and inception 3 ways both have allen key holes in the front of the 3 ways to make adjustment easier. Shocktech has a allen key hole in the ram shaft. Inception ram supposedly uses less pressure, though i have not tested it. Wrench flats and holes to be able to remove the pump arm easier. Not ground breaking, but nice stuff to have.

Used stuff: https://www.mcarterbrown.com/forum/b...riday-part-two
New Stuff:https://beardedworks.com/

[flavordeliverer]

Thanks superman! I'll send a DM about parts real soon.

[woouulf]

I'm out, just to vague...I cant see spending hours listing parts...

[flavordeliverer]

woouulf Oh yeah. Totally get that. I expect a lot of members to get scrolling when they see this post!

[BrendanB]

its far cheaper to get a complete build than to build one from parts IMHO unless you just want the thrill of the build which i can understand

[Daltech]

Buy 3, scrap parts off them, and voila! Your an instant Autococker parts hoarder.

[Riot]

Lot of people bored today? All these replies and only one answer to OP.
I'll look through my stuff later this week (working a bunch the next few days) and ill shoot you some pictures over. I have some things like rods, beavertails, maybe even pnuematics. I have no idea what they're to or where they go, so, ill gladly offload anything you may need.

[flavordeliverer]

Thanks a bunch! I don't have any parts at all yet (even a body Cdn_Cuda ) so I'm open to whatever.

I've been looking at bodies. What should I be looking specifically for to open up my options the most?

[Cdn_Cuda]

It helps if we know what body style you have or are looking at. Pre-2k vs Post 2k and then whether it's a 11/16 valve (Trilogy cockers, 2k5 Black Magics etc) or a 9/16 valve (standard cocker valve). If you haven't gotten a body yet, start there at is will affect bolt, internals etc.

[flavordeliverer]

BrendanB I'm in it for the thrill. I know it's cheaper to buy a full gun but I haven't been able to 'make' something in a while so figured this would satisfy that.

Daltech totally down to do that. I'm fairly limited on space so I'm trying to keep hoarding to a minimum. (yeah right)

[BrendanB]

ok so you need:

body with back block, vasa (if full body) and front block (front block and vasa would be together if its a mini body)
(body could have built in feedneck or need a feedneck like an inception or geo depending on if its empire cut or eclipse cut neck job)
pneumatics: ram, lpr, 3way
timing rod (mini or standard)
pump arm (most mini or full, but also halfblock, halfblock mini)
bolt and pin (pre2k, 2k or evo length depending on combo of body and block, could be a half or midblock too)
high pressure regulator (hpr)
frame (slider or hinge)
asa (duckbill simple, or on/off style)
macro line fittings connect line from hpr to asa
mini hose for pnues
lower tube: hammer with lug and spring valve with spring ivg (11/16th or 9/16th valves)
cocking rod (for back block)
barrel
grips/panels

[flavordeliverer]

Appreciate that! I'll copy and pasta into original post for record.

[Walker]

Some of BrendanB's list is variable, depending on what body you get to work with.... Mini/full, pre2k/2k.......

[Daltech]

[flavordeliverer]

Slowly working on this! Is anyone able to compile and sell nice easily-adjustable ram, LPR, and 3-way? I’m trying to focus on quality front pneumatics

[superman]

Raises hand 🙋♂️