Sheridan "tuning".

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • gabe
    replied
    My sheridan pistols barely will pierce a 12 gram. Like just a little pinhole in the 12gram face is what I'll see. Normally takes 2-3 strikes to pierce. 25 shots per 12gram that way.

    Leave a comment:


  • Jordan
    replied
    Originally posted by Spider!
    I'm not sure about KPs, but that is huge for a Sheridan pistol.
    Really? How small is normal? This looks to roughly 0.035"ish. I think the shadowing in the picture makes it look bigger.

    Leave a comment:


  • Spider!
    replied
    I'm not sure about KPs, but that is huge for a Sheridan pistol.

    Even the old turbo valves created pressure sensitivity due to their high flow, but we used them more for bulk CO2 tanks.

    Leave a comment:


  • Jordan
    replied
    Here's what the puncture size looks like.

    20211103_181455.jpg
    Last edited by Jordan; 11-03-2021, 06:15 PM.

    Leave a comment:


  • Jordan
    replied
    Originally posted by BrickHaus
    I wish I had some insights for you. I typically am trying to make sheridans work on hpa, so its a more flow, more spring mentality. I was surprised to see your valve plugs you did to make yours efficient. If the pierce is too much, is it viable to to restrict the valves output if the pierce hole isnt working?

    Tap the other 2 valve holes, plug, and drill the plug out smaller?
    I think that's my problem too... I'm so used to trying to improve performance with HPA that I'm worried I overdid it. 🙂

    I did scrounge up a red Cocker valve spring that I've trimmed to fit and just installed it... preliminary testing shows some better shot count, but it's getting too cold to really check properly at this point.

    Leave a comment:


  • BrickHaus
    replied
    I wish I had some insights for you. I typically am trying to make sheridans work on hpa, so its a more flow, more spring mentality. I was surprised to see your valve plugs you did to make yours efficient. If the pierce is too much, is it viable to to restrict the valves output if the pierce hole isnt working?

    Tap the other 2 valve holes, plug, and drill the plug out smaller?

    Leave a comment:


  • Jordan
    replied
    Originally posted by Spider!
    Sounds like the valve spring is too light for the setup. 2c
    Could be... it's from PPS, I didn't have an original one.

    Leave a comment:


  • Spider!
    replied
    Sounds like the valve spring is too light for the setup. 2c

    Leave a comment:


  • Jordan
    replied
    Originally posted by Spider!
    What kind of pierce do you have?

    BretG used to advise that you want a tiny hole to "sip" the CO2. It kind of goes along with the various kinds of flow restrictions used on different markers.

    You need to separate the reservoir of the 12g cartridge from the dump chamber with a restriction. Auto/self pierce pins tend to have large holes, which then feed directly to the Sheridan dump chamber.
    Shoot to pierce Dynavalve.

    I actually trimmed the pierce pin down a bit, it was getting stuck in the 12 gram. Looks fairly concentric.

    Leave a comment:


  • Spider!
    replied
    What kind of pierce do you have?

    BretG used to advise that you want a tiny hole to "sip" the CO2. It kind of goes along with the various kinds of flow restrictions used on different markers.

    You need to separate the reservoir of the 12g cartridge from the dump chamber with a restriction. Auto/self pierce pins tend to have large holes, which then feed directly to the Sheridan dump chamber.

    Leave a comment:


  • Jordan
    commented on 's reply
    I probably get about 20ish, but most go about 15 feet.

  • RAZRBAKK
    replied
    5 shots? Jeez, make em count.

    Leave a comment:


  • Jordan
    replied
    Originally posted by netsurferdude2
    5 shots is no good.

    Off the top of my head:
    Clean lower tube, polish hammer, clean valve, change valve spring, replace seals, clean pierce pin, enlarge transfer port, use dyna valve
    All done already.

    🙂

    Brand new hammer, mainspring, valve spring, Dynavalve, valve with ported passageways, enlarged the transfer port, enlarged bolt passageways. I even put wedgits in.

    No baseline, most of those parts were missing when i got the KP.

    Leave a comment:


  • netsurferdude2
    replied
    5 shots is no good.

    Off the top of my head:
    Clean lower tube, polish hammer, clean valve, change valve spring, replace seals, clean pierce pin, enlarge transfer port, use dyna valve

    Leave a comment:


  • Jordan
    started a topic Sheridan "tuning".

    Sheridan "tuning".

    Can 12 gram Sheridans be tweaked like Snipers/Cockers?

    My KP gets about 5 good shots from a 12gram, the rest are what I would consider unuseable.

    I cut a couple coils to try to reduce the two initial hot shots and I've achieved that but seem to reduced overall velocity now, which is frustrating to say the least.
Working...