CCI Phantom/Nelson Cup Seal replacements available.

[Myfeetupontheground]

Hey everybody! I have heard back from my customers that the Face Seals I am making for the PGP also work on the CCI Phantom / Nelson cup seals. Just fyi, if that is something you are needing.

5 seals - $10

PGPJunkies.bigcartel.com

[Magageddon]

cup seals or 12 gram changer pierce pin seals? they look a little too small diameter for the inner hole to work as cup seals?

[Myfeetupontheground]

I am just going on the feedback I am getting.
https://youtu.be/w7IO29IOlao?si=3WIHnBFsFLMzhhG8

[Chaos]

What he's selling will only work as a Sheridan Faceseal and a Phantom style Cupseal. These are not for the bucket changers but those are hopefully in the works

[Chuck E Ducky]

Chaos has been testing these out. So far good results?

[Chaos]

So far so good ..letting it sit gased up overnight and see if it holds, pretty sure it will

[Chaos]

The gun has been sitting gassed up overnight and it's still holding air

[Chaos]

To clarify Phantom Cupseals and Sheridan Faceseals (12g seals) are the exact same size and shape as each other. The seals for sale here will work for either set up. These are not the same as Phantom bucket changers seals but I did send one to him to copy so hopefully those will be available soon



Just tested the Faceseals out tonight and they work great. Here's a test video
https://youtu.be/w7IO29IOlao?si=SVCid-WtquMwZph1

[Myfeetupontheground]

To clarify Phantom Cupseals and Sheridan Faceseals (12g seals) are the exact same size and shape as each other. The seals for sale here will work for either set up. These are not the same as Phantom bucket changers seals but I did send one to him to copy so hopefully those will be available soon



Just tested the Faceseals out tonight and they work great. Here's a test video
https://youtu.be/w7IO29IOlao?si=SVCid-WtquMwZph1

I had to order some higher duro (and thinner) rubber to begin experimenting on the seal you sent. I should have it by next week. It may be a long process, because I will likely have to send them to you for testing each time I make one. Haha

[Chaos]

Myfeetupontheground That's fine, I don't mind testing them out for you. I have a Semi pistol that uses those type of seals which is very hard on those seals when changing out the cartridges, so it'll give them a good solid test

[Hutbrew]

I would buy 5-10 if someone was to make a replacement for the little “half donuts” that are the hard seal on trracer valves

[Chaos]

Someone might be able to do that, but just so you know a Kingman Hammer cupseal makes a great replacement for those

[Hutbrew]

I have some on those- they might be regular Spyder ones- can I just rip off the donut+ brass cup seal, replacing it with only the white plastic Spyder hammer seal? I wasn’t sure how with the concavity of the valve piece the donut sits in

[Chaos]

You can remove the donut and brass and replace them with one from a Hammer...not the same as a Spyder

[Chaos]

I have some on those- they might be regular Spyder ones- can I just rip off the donut+ brass cup seal, replacing it with only the white plastic Spyder hammer seal? I wasn’t sure how with the concavity of the valve piece the donut sits in

These are what you can replace them with one from a Spyder will not work correctly. These have the concave part as part of them. Keep in mind Hammers and Trracers share many compatible parts..

[Hutbrew]

Ah- this is not what I have

thanks!

[Chaos]

NP Man