Sold!
For Sale: AGD MiniMag, s# 13847 Price: $200.00 shipped, OBRO
AGD Classic MiniMag
- Body: PowerFeed Hopper Right
- Valve: Classic MiniMag, matching S# MM13847
- On/Off: Stock
- Bolt: Venturi, level 7
- Barrel: Dye twistlock (10-inch Stainless) and the stock barrel
- Frame: Stock, Metal, safety functional
- Grips: AGD rubber
- ASA: Duckbill
- Original box, manual, notice, sticker, and VHS tape. Box is not perfect, when it was shipped to me the feedneck put a hole in it.
Notes:
1. Tested with HPA, no leaks detected, cycles ok. YMMV
2. FPS with initial reg setup shown below..
3. Gun is sold As-Is....
4. Rail and vertical adapter are in very nice shape.
5. No rollouts with Reballs... Go figure.... The plastic ball detent is doing its job.
6. Replaced:
- Power Tube oring (has a .225 spacer installed)
- Power tube tip oring
- Bolt bumper
- On/Off orings
- Reg seat
- Reg piston oring
- Reg half oring
- Barrel orings and detent
- QD oring at the valve connection
- Original frame was a cut composite, replaced with uncut AGD metal frame
Chrono results:
Ten Shots, initial gun setup, reballs, HPA tank @ 800psi output, Dye 10-inch twistlock barrel
(Note: I did not turn the velocity down after the initial setup)
Low: 298.2
High: 319.4
Average: 308.0
Shots:
10. 319.4
9. 308.6
8. 308.5
7. 313.0
6. 298.2
5. 307.7
4. 313.2
3. 299.5
2. 311.9
1. 300.4
Advice: As always with a used AutoMag, pick up a Parts Kit to have on-hand.
Trades: None that I can think of.
Payment: PayPal preferred, FF appreciated but not required.
Shipping: USPS Priority within the US.
Post and/or PM if you have questions.
Thanks for looking!
Walker
For Sale: AGD MiniMag, s# 13847 Price: $200.00 shipped, OBRO
AGD Classic MiniMag
- Body: PowerFeed Hopper Right
- Valve: Classic MiniMag, matching S# MM13847
- On/Off: Stock
- Bolt: Venturi, level 7
- Barrel: Dye twistlock (10-inch Stainless) and the stock barrel
- Frame: Stock, Metal, safety functional
- Grips: AGD rubber
- ASA: Duckbill
- Original box, manual, notice, sticker, and VHS tape. Box is not perfect, when it was shipped to me the feedneck put a hole in it.
Notes:
1. Tested with HPA, no leaks detected, cycles ok. YMMV
2. FPS with initial reg setup shown below..
3. Gun is sold As-Is....
4. Rail and vertical adapter are in very nice shape.
5. No rollouts with Reballs... Go figure.... The plastic ball detent is doing its job.
6. Replaced:
- Power Tube oring (has a .225 spacer installed)
- Power tube tip oring
- Bolt bumper
- On/Off orings
- Reg seat
- Reg piston oring
- Reg half oring
- Barrel orings and detent
- QD oring at the valve connection
- Original frame was a cut composite, replaced with uncut AGD metal frame
Chrono results:
Ten Shots, initial gun setup, reballs, HPA tank @ 800psi output, Dye 10-inch twistlock barrel
(Note: I did not turn the velocity down after the initial setup)
Low: 298.2
High: 319.4
Average: 308.0
Shots:
10. 319.4
9. 308.6
8. 308.5
7. 313.0
6. 298.2
5. 307.7
4. 313.2
3. 299.5
2. 311.9
1. 300.4
Advice: As always with a used AutoMag, pick up a Parts Kit to have on-hand.
Trades: None that I can think of.
Payment: PayPal preferred, FF appreciated but not required.
Shipping: USPS Priority within the US.
Post and/or PM if you have questions.
Thanks for looking!
Walker
Comment