Sheridan "tuning".

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Jordan
    I. Am. Canadian. 🇨🇦
    • Jul 2020
    • 3507
    • Southern Ontario, Canada

    #1

    Sheridan "tuning".

    Can 12 gram Sheridans be tweaked like Snipers/Cockers?

    My KP gets about 5 good shots from a 12gram, the rest are what I would consider unuseable.

    I cut a couple coils to try to reduce the two initial hot shots and I've achieved that but seem to reduced overall velocity now, which is frustrating to say the least.
  • netsurferdude2
    MCB Member
    • Jul 2020
    • 879
    • North of Bawlmer

    #2
    5 shots is no good.

    Off the top of my head:
    Clean lower tube, polish hammer, clean valve, change valve spring, replace seals, clean pierce pin, enlarge transfer port, use dyna valve

    Comment

    • Jordan
      I. Am. Canadian. 🇨🇦
      • Jul 2020
      • 3507
      • Southern Ontario, Canada

      #3
      Originally posted by netsurferdude2
      5 shots is no good.

      Off the top of my head:
      Clean lower tube, polish hammer, clean valve, change valve spring, replace seals, clean pierce pin, enlarge transfer port, use dyna valve
      All done already.

      🙂

      Brand new hammer, mainspring, valve spring, Dynavalve, valve with ported passageways, enlarged the transfer port, enlarged bolt passageways. I even put wedgits in.

      No baseline, most of those parts were missing when i got the KP.

      Comment

      • RAZRBAKK
        Unburdened by genius.
        • Jul 2020
        • 1388
        • Calgary, Alberta

        #4
        5 shots? Jeez, make em count.
        Originally posted by Terry A. Davis
        God said 640x480 16 color was a covenant like circumcision.

        Comment


        • Jordan
          Jordan commented
          Editing a comment
          I probably get about 20ish, but most go about 15 feet.
      • Spider!
        MCB Member
        • Jul 2020
        • 542
        • Houston

        #5
        What kind of pierce do you have?

        BretG used to advise that you want a tiny hole to "sip" the CO2. It kind of goes along with the various kinds of flow restrictions used on different markers.

        You need to separate the reservoir of the 12g cartridge from the dump chamber with a restriction. Auto/self pierce pins tend to have large holes, which then feed directly to the Sheridan dump chamber.
        Feedback

        https://www.mcarterbrown.com/forum/b...der-s-feedback

        Comment

        • Jordan
          I. Am. Canadian. 🇨🇦
          • Jul 2020
          • 3507
          • Southern Ontario, Canada

          #6
          Originally posted by Spider!
          What kind of pierce do you have?

          BretG used to advise that you want a tiny hole to "sip" the CO2. It kind of goes along with the various kinds of flow restrictions used on different markers.

          You need to separate the reservoir of the 12g cartridge from the dump chamber with a restriction. Auto/self pierce pins tend to have large holes, which then feed directly to the Sheridan dump chamber.
          Shoot to pierce Dynavalve.

          I actually trimmed the pierce pin down a bit, it was getting stuck in the 12 gram. Looks fairly concentric.

          Comment

          • Spider!
            MCB Member
            • Jul 2020
            • 542
            • Houston

            #7
            Sounds like the valve spring is too light for the setup. 2c
            Feedback

            https://www.mcarterbrown.com/forum/b...der-s-feedback

            Comment

            • Jordan
              I. Am. Canadian. 🇨🇦
              • Jul 2020
              • 3507
              • Southern Ontario, Canada

              #8
              Originally posted by Spider!
              Sounds like the valve spring is too light for the setup. 2c
              Could be... it's from PPS, I didn't have an original one.

              Comment

              • BrickHaus
                Tactical Spoon Reacquired
                • Sep 2020
                • 3397
                • Minnesota

                #9
                I wish I had some insights for you. I typically am trying to make sheridans work on hpa, so its a more flow, more spring mentality. I was surprised to see your valve plugs you did to make yours efficient. If the pierce is too much, is it viable to to restrict the valves output if the pierce hole isnt working?

                Tap the other 2 valve holes, plug, and drill the plug out smaller?
                https://www.mcarterbrown.com/forum/b...khaus-feedback

                Comment

                • Jordan
                  I. Am. Canadian. 🇨🇦
                  • Jul 2020
                  • 3507
                  • Southern Ontario, Canada

                  #10
                  Originally posted by BrickHaus
                  I wish I had some insights for you. I typically am trying to make sheridans work on hpa, so its a more flow, more spring mentality. I was surprised to see your valve plugs you did to make yours efficient. If the pierce is too much, is it viable to to restrict the valves output if the pierce hole isnt working?

                  Tap the other 2 valve holes, plug, and drill the plug out smaller?
                  I think that's my problem too... I'm so used to trying to improve performance with HPA that I'm worried I overdid it. 🙂

                  I did scrounge up a red Cocker valve spring that I've trimmed to fit and just installed it... preliminary testing shows some better shot count, but it's getting too cold to really check properly at this point.

                  Comment

                  • Jordan
                    I. Am. Canadian. 🇨🇦
                    • Jul 2020
                    • 3507
                    • Southern Ontario, Canada

                    #11
                    Here's what the puncture size looks like.

                    20211103_181455.jpg
                    Last edited by Jordan; 11-03-2021, 06:15 PM.

                    Comment

                    • Spider!
                      MCB Member
                      • Jul 2020
                      • 542
                      • Houston

                      #12
                      I'm not sure about KPs, but that is huge for a Sheridan pistol.

                      Even the old turbo valves created pressure sensitivity due to their high flow, but we used them more for bulk CO2 tanks.
                      Feedback

                      https://www.mcarterbrown.com/forum/b...der-s-feedback

                      Comment

                      • Jordan
                        I. Am. Canadian. 🇨🇦
                        • Jul 2020
                        • 3507
                        • Southern Ontario, Canada

                        #13
                        Originally posted by Spider!
                        I'm not sure about KPs, but that is huge for a Sheridan pistol.
                        Really? How small is normal? This looks to roughly 0.035"ish. I think the shadowing in the picture makes it look bigger.

                        Comment

                        • gabe
                          Thirst Trappin
                          • Jul 2020
                          • 1079
                          • Alaska

                          #14
                          My sheridan pistols barely will pierce a 12 gram. Like just a little pinhole in the 12gram face is what I'll see. Normally takes 2-3 strikes to pierce. 25 shots per 12gram that way.

                          Comment

                          • Spider!
                            MCB Member
                            • Jul 2020
                            • 542
                            • Houston

                            #15
                            Originally posted by Jordan

                            Really? How small is normal?
                            A barely visible hole is still functional. That's when the piercing is iffy, so it's usually a little larger. It should be the point through the seal. Does the valve body have a cone on it that the pin travels through? That's a big dish around the hole.
                            Feedback

                            https://www.mcarterbrown.com/forum/b...der-s-feedback

                            Comment

                            Working...