A deadly winds.... What?

[Ecapnation]

I think this is for an sp1 or a vibe but I'm not exactly sure what the hell I'm looking at nor can I verify that they actually made this. It looks similar to their hollow point bolt for the ion but has a back half that might be intended for an sp1.

[jetenginekyle]

Might be for deadlywind's bolt out back ion bodies? There was also that chromed out ion that was bolt out back think it was called epiphany

[Trbo323]

I'd also look at the DP g3 or 4. Those bolts were pretty similar

Sent from my motorola edge 5G UW (2021) using Tapatalk

[martix_agent]

The easiest way to answer this is maybe to contact DW themself. They might know.

At 1:40, he takes the bolt out of the gun. The back of it looks like yours, but from your photo it's hard to tell if it's the same as what you have. His has a sleeve on it because the body isn't solid.

https://www.youtube.com/watch?v=tJCYSbGvFBk

[Siress]

looks like a Dangerous Power spool valve train... E1 maybe?

might not be a DW product...

[uv_halo]

Deadlywind Hollowpoint Bolt Stalk for SP1 / Vibe / Ion XE and a Deadlywind Hollowpoint Bolt (non U3 version). This combo may not work with the previously mentioned guns if they are using a QEV. for QEV applications, they recommend the U3, rubber tipped bolt to prevent / reduce breach breaks.

[Ecapnation]

Eh.... Got it in a lot so just trying to pin down what it is. I don't ion/sp1 anymore

[The Hobbit]

That doesn’t appear correct for an ion based marker. I’m leaning towards a Dangerous Power product particularly a G3.

[Psycho91]

From my little bit of research that seems to be for a g3 or 4

[Trbo323]

From my little bit of research that seems to be for a g3 or 4

*polishes fingernails on shirt*

Sent from my motorola edge 5G UW (2021) using Tapatalk

[uv_halo]

If I remember correctly, I put a Deadlywing bolt in my Sp-1. I will break it out tonight and upload a pic.
Somethings to consider:
1. Deadlywind never made bolts for DP guns.
2. Deadlywind sold their bolt kits in packaging just like the OP's.
3. The Vibe / SP1 and the Ion XE (which Deadlywind did produce bolts for), are all built out of the box for "Bolt Out the Back" In the stock configuration, these markers use a threaded endcap like the OPs but, with a fixed insert (with holes) to devolumize the fire chamber. The Deadlywind part omits the insert and instead uses a thicker core than the original (deadlywind) bolt stalk for similar effect.

[Ecapnation]

I'm assuming it's ion xe or sp1 something as well....

I just don't feel like digging one out to check as they are way back in the storage room

[uv_halo]

I apologize for the delay. Here's the bolt and bolt stalk combo I pulled out of my Smart Parts SP-1:

[Ecapnation]

How hard is it to set? Debating what to do with it

[uv_halo]

@Ecapnation: I'm not sure what you mean by "How hard is it to set". As for setting it up, it's more or less a direct swap. You remove the back cover off the Sp-1, unthread the bolt sleeve and remove the bolt and bolt stop. The assembly above will slide right in. The dwell might need to be adjusted but, I can't say for sure (I don't have the factory board in my Sp-1 anymore).

[Ecapnation]

Interesting... Just the dwell I was concerned about.

I have a black heart so I can tinker