I have a Powerhouse TKO set to 650psi. Will a Ninja SHP allow me to get the most out of the RT on my mags? I can get bursts of the RT but no real strings.
-
WTS (PM me) | Black X-Mag | Blue/Silver E-Mag | 68 Automag | Dye M3+ | Invert Mini | PMR | CCI Phantom | PTP RF Autococker | WGP '98 RF Autococker | Trilogy Pro | Spyder MR2 | Diablo Wrath | Tippmann A-5 LPK | 98 Custom x3 | E-Bolt Model 98 | FT-12
WTB | Tippmann LPK
Wishlist | Karnivor | CF Blazer | 2K12 G6R | AKA Viking | Everything -
Depends on the setup, but you usually need more than 800 PSI to get things going. More in the 950 PSI territory. -
You can contact Powerhouse for the parts needed to bring that reg up to over 950. I think AGD was selling them too.Comment
-
depends on how fast you want to shoot 😂. anyone remember this video
Comment
-
Im pretty disappointed that powerhouse won’t make reg seats for there first gen regulators. It’s not like they were cheap regs to begin with. But I can’t deny I'm a lil butt hurt that I can’t buy a dam replacement reg seat for one of my regulators that self destructed when a piece of burst disk scored the reg seat that is no longer replaceable. Powerhouse did offer $50 off any of there $250 regulators. I have other power house regs that are newer and they still offer parts for now. But that situation really grinds my gears.
I still think they make quality regulators likely the best. But I have ninjas that are twice as old and the company is out of business and I can still get reg seats for them and they are half the cost 🤷🏻Comment
-
If your idea is to get the most out of the 'rt' effect, shortening your on/off pin should be where you go firstLast edited by alpha_q_up; 02-04-2026, 03:00 PM.Comment
-
Contacted Courtney from Infinite Paintball/Powerhouse. It sounds like the high pressure springs are custom made. Mine will be made by the tech tomorrow. $9.99 for the spring and a colonoscopy for the tool.WTS (PM me) | Black X-Mag | Blue/Silver E-Mag | 68 Automag | Dye M3+ | Invert Mini | PMR | CCI Phantom | PTP RF Autococker | WGP '98 RF Autococker | Trilogy Pro | Spyder MR2 | Diablo Wrath | Tippmann A-5 LPK | 98 Custom x3 | E-Bolt Model 98 | FT-12
WTB | Tippmann LPK
Wishlist | Karnivor | CF Blazer | 2K12 G6R | AKA Viking | EverythingComment
-
For RT stupidity you want like 1200psi
850 is base line.Comment
-
You can buy cheap knock off pure energy type regs for air rifles.Comment
-
They are on Amazon you want 1000, 1200 or 1800 they are like $26-$36 I used to use the 1000’s to make My DamHammer7 shoot field speeds on HPA. They work good and are basically the same exact design inside as the old pure energy regs that nobody ever thought about because they worked flawlessly for ever. All the air rifle sights sell them to if you want to shop around. There is even one with an adjusting knob that goes inside the tank that you can manually adjust output up or down starting at 800-2k (I wouldn’t go that high)
-
What they all said..... when I re-built my RT it didn't do diddly shiddly till I got a reg with a range of 900- 1200 psi from powerhouse. Its a combo of shortening on/off, input PSI and very importantly break in if you just re-built it with new o-rings. I need to get mine out again and really try to try to get it to obsurd levels. the more paint i ran through it the better it shot. I don't really like playing with it but it sure is fun to have around and tinker with.Comment
-
It has the .712 pin.
That's what I like about this E-Mag. Semi, RT, or electronic to shoot 10.2 ramping. It’s a good-looker but not spotless so I don't mind playing with it.
I installed the custom spring, shims, and set the TKO to 1,100psi. This thing is nuts.Last edited by trashcollector; 02-16-2026, 09:42 PM.WTS (PM me) | Black X-Mag | Blue/Silver E-Mag | 68 Automag | Dye M3+ | Invert Mini | PMR | CCI Phantom | PTP RF Autococker | WGP '98 RF Autococker | Trilogy Pro | Spyder MR2 | Diablo Wrath | Tippmann A-5 LPK | 98 Custom x3 | E-Bolt Model 98 | FT-12
WTB | Tippmann LPK
Wishlist | Karnivor | CF Blazer | 2K12 G6R | AKA Viking | EverythingComment
-
Comment