Welcome to MCB! We are the most popular and active paintball forum found on the internet! Thank you for stopping by.
If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
The new site changes also meant cookie changes. Sorry. Unavoidable. If you're getting logged out, you need to clear your browser cache / data and cookies. Then when you log back in, you will be all set. More HERE on what's happening next.
As far as I know, Pimps take a 2k2 Timmy LPR, but I'm not up on what parts fit what generation.
I know I'll need a solution for the valve spring, but I think I have that part figured out.
I believe everything pre-g6r/protege have the same lpr threads though the gen 1 timmys had a different internal layout where the valve was in the front block and the lpr house was just the spring and piston.
I was at one point looking to see if someone would make me a valve body or adapter to drop a morph valve into the pimp so I didnt have to worry about the valve spring. Just couldn't get anyone to make it for me.
The AKA SCM Timmy LPR and AKA Timmy volumizer both fit perfectly on my Pimp.
But my Pimp has a RIP valve in it, so I don't have to worry about the valve spring still fitting.
The Evil LPR has a wierd brass base to it, or mine did, and won't sit in a Timmy volumizer correctly due to that brass piece. So there are differences.
My Pimp came with a Hybrid Timmy LPR, if that's any help.
If you need to talk, I will listen. Leave a message and I will call you back as soon as I get it.
IGY6; 503.995.0257
The AKA SCM Timmy LPR and AKA Timmy volumizer both fit perfectly on my Pimp.
But my Pimp has a RIP valve in it, so I don't have to worry about the valve spring still fitting.
The Evil LPR has a wierd brass base to it, or mine did, and won't sit in a Timmy volumizer correctly due to that brass piece. So there are differences.
My Pimp came with a Hybrid Timmy LPR, if that's any help.
It helps a bit - thanks.
Part of my interest in an aftermarket solution lies in the fact that, to the best of my knowledge, Respirator reg seats are not available. I will have to install something else when the seat fails on my LPR, and I figure I'll look now rather than get caught short.
I like these old weird guns but trying to find replacement parts can be a challenge if their designer didn't future-proof them.
I don't know the internal condition of my Respirator LPR... but I can send it your way when I pull it out of storage.
If you are actually willing to rebuild your own Respirator, I will send you mine so you have some spare parts to work with.
I am not willing to mess the magical strips of plastic sandwich bag BS, so hanging on to my Respirator just because it is Evil would be selfish and stupid.
If you need to talk, I will listen. Leave a message and I will call you back as soon as I get it.
IGY6; 503.995.0257
I don't know the internal condition of my Respirator LPR... but I can send it your way when I pull it out of storage.
If you are actually willing to rebuild your own Respirator, I will send you mine so you have some spare parts to work with.
I am not willing to mess the magical strips of plastic sandwich bag BS, so hanging on to my Respirator just because it is Evil would be selfish and stupid.
I did rebuild mine (since I'm not in a position to buy a Rock right now) and it's working fine once I remembered they're not happy being adjusted when aired up. Turns out you don't need a plastic strip if you give the piston a good squeeze and wiggle when installing it into the lower housing.
I just finished rebuilding the Detonator as well... turns out Sledgehammer LPR seats are a close match to Detonator reg seats and work great.
Eventually I will end up installing a Rock but for now everything works and I've got next to nothing invested in other than time.
Comment