I'm at a loss as to what to do with it? Part, trade, hang from the wall? Rebuild is an option too but probably the last one. Realistically I don't see myself ever using it.
-
Found this in my basement recently. I think I built it in the 90s and just forgot about it. The tank is out of hydro by 23 years so I can't air it up with what I have lying around nor do I have a hopper that easily fits the warp. Built mags aren't really my thing anymore, I would rather just have a clean and simple one. I diy'd a lot of stuff on it like putting a feed switch in the frame and cutting the stock rail to fit the ule body. Looks like I cut the front off the body as well for reasons I can't remember. Lvl 7 ANS bolt with shock tech reg housing. Warpfeed is complete and works, I think.
I'm at a loss as to what to do with it? Part, trade, hang from the wall? Rebuild is an option too but probably the last one. Realistically I don't see myself ever using it.
-
Scuttle the tanks, but a new drop and ASA, find a hopper that will work with the warp and enjoy the lunacy of it! Picked up a classic valved mag with a warpfeed and despite the mass of it it was stupid fun to play with. You can always part the warpfeed and body and get a standard body for the mag.-
How do you dispose of a tank that can’t be hydro? Empty the air and throw in the trash? -
To decommission a HPA tank drain it of air, remove the regulator and drill a hole through the tank preventing it from every being recharged again. IIRC it calls for a 3/8 in hole. Decommissioning a Fiber Wrapped bottles is called out in the CFR documentation. -
Fill it with tannerite and take it to the range.
No hurry, just wait until the next time you’re making more tannerite-filled Lawn Gnomes and birdhouses as decorations for yours and your neighbors yards.
-
-
Drill a hole in it and toss it, if it's a cheap aluminum tank drill a hole and recycle itComment
-
I give my dead tanks to my local dive shop to dispose of. I also usually give them my CO2 tanks for free as I don't need or want them.Comment
-
I would think harvesting the regulator would be worth it in most cases?
Comment
-
Not really, since the reg relies on the cradle drop you would have to get a new bottle and then run that reg. That also means you are relying on that 28ish year old reg seat with a slim chance of getting a new one.
Pitch the reg and tank and drop, move to a 2 hole direct mount drop and ASA setup then you can screw any tank you want into it without having the tank tied to this specific marker
Sent from my motorola edge 2024 using Tapatalk
I use Tapatalk which does NOT display comments. If you want me to see it, make it a post not a comment.
Feedback
https://www.mcarterbrown.com/forum/b...323-s-feedbackComment
-
How did you just come across this in the basement? What else do you have hidden down there hahaComment
-
Mostly really old stuff that's been in totes for decades. Lots of old gear from the 90s, lots of spiders, couple vm68, trilogy converted pump, a basic automag, old taso vindicator and an evil minion are the most notable. Sadly all my spare parts are gone so I'm trying to work with what I have left. Get the ones running that I can and get rid of the rest.
-
-
Fix it up and use it, you definitely will get some attention at the field over it. Contrary to what some are saying above I'm not sure I would dump the cradle, your current setup is very similar to my Warp Fed Mag I played for quite a while. I used the same Kapp cradle so I could mount the bottle to the right to offset the weight of the Warp feed, loader and paint on the left. A warp setup with the bottle in line to the marker is very unbalanced to the left.
"When you are asked if you can do a job, tell 'em, 'Certainly I can!' Then get busy and find out how to do it." - Theodore Roosevelt
Feedback Link - https://www.mcarterbrown.com/forum/b...del-s-feedbackComment
-
Comment
-
Here's a better image of the drop forward with an on/off asa. This is the one I used to use on my sniper so you can see a cage style ASA on/off works in the drop forward just as well as the Reg body.
Last edited by Grendel; 02-21-2025, 02:58 PM.
"When you are asked if you can do a job, tell 'em, 'Certainly I can!' Then get busy and find out how to do it." - Theodore Roosevelt
Feedback Link - https://www.mcarterbrown.com/forum/b...del-s-feedbackComment
-
Let see pictures of this hidden booty in those totesComment
-
They have been out of the tote for a while now lol. I have a bunch of it away at games and worked on\cleaned the rest. Probably a dozen or so guns in the tote. The newest gun was a minty evil minion pm7. Oldest was either a splatmaster or the taso vindicator.
I found another mag that was stock in there that I use quite a bit now. I don't really use the warp feed one. Got it shooting good and just put it on a shelf.Comment
-
Man I have that exact same kapp drop forward on my Gen 1 intimidator. Is that an air America raptor rex reg? I’m asking because I also have that reg on a kapp drop foward and looks identical from the pic. My tank was also out of hydro for 20 years, however, I got a rebuild kit for the raptor rex regulator for $20 and its adjustable up to either 1000psi or 11000psi if I remember right and that’s perfect for an autopay or other classic markers. I’ve found smaller mounting brackets for the reg so you don’t have to have a massive drop forward. I’m working on two automags right now but once I get them figured out I’m going to rebuild the reg and put a new tank on it. I think it would be easier to get running than you think and pretty cool
If you decided to sell it, let me knowComment
Comment