The Official CCI Picture Thread

[Walker]

urban_camo.JPG
woodland.jpg
Urbanphantom.jpg

[JeepDVLZ45]

E7663F16-057F-4753-826B-E90E3B72E695.jpeg

New to me….unmolested DuckSlide

[Pogi Si David]

My “One to rule them all”

[JeeperCreeper]

I love this

[frd333do33]

That purple on the inside is *chef's kiss*

[Cunha]

Who did this anodizing? Righteous.

[Impactfour]

My current set-up. Mike Holts working on a matching green pump handle that's as long as the spring feed when cocked. There's also a green/silver asa somewhere offscreen. Someday I'll have collected all the parts and then I'll either get them anodized to match or get everything done up with a new anno job.

[JeeperCreeper]

Gonna try this setup out. Thanks again redsquirrel for the dropout changer.

[Impactfour]

Pretty sure paintball gateway has black/blue acid wash barrels available if you're looking to make everything matching.

[NONOBLITUS]

Just figured I would throw a picture of this in here as well. Nice sunny day out so why not a photo.
9C602897-B3BF-4D95-9B97-277E86BF5BA3.jpeg

[NONOBLITUS]

Not absolutely sure honestly. I have not seen many like this

[Melrosejedi]

The stock is an “ in yo face”. I run them on my karnis and they are super. Hard to find these days.

[Pump&Run]

I have two …one is a marked In Yo Face stock and the second is marked P.M.I. … same exact stocks

[luckyduck]

Here’s mine!

[JeepDVLZ45]

You could also brass plate the rear body screw. I did it with one of my old pantoms it’s pretty simple and really helps brass everything out!

Looks great

[luckyduck]

Great ideas !

[JeepDVLZ45]

When you can PM, shoot me your address. I think I actually have one in my box o’bits that I had done for a different marker. I’ll send it out to you….I’ll look to see if I have any ones I did for the hogues too. If I do I’ll send them too.

(I tried doing the pump rails and pump rod as well, but it didn’t hold the plating)

[Impactfour]

My current micro phantom set up. If I can get the funds together I'm going to buy a few more pieces and get them all annodized to match

[frd333do33]

What pieces are you going to get?

[Impactfour]

In matching I currently have but not pictured: VSC Air set up, asa, 11" and 14" barrels, 15 Rd feed tube.

The list of parts I need to anno to match but have are the 45* frame, dual rod undercocking mount, ICD changer and it's corresponding valve.

Parts I need to order and anno, or find matched are CCI bucket changer assembly, dropout valve, aluminum grips and pump plate/handle ala ODM. Hell id even toss a duckslide into the mix if I could aquire it.

These are slow developing long term plans. I just want to have every possible assembly I could want to use in the matching anno I like.

[RayOdder]

[Db1060]

how does that peacemaker work? cock it and it drops 2 balls from the top? never seen one.

[RayOdder]

Yes, there is hole on the bottom of the top breach that allows a ball to drop down to the breach below. To fire it the trigger trips the sear holding the bottom hammer which has pin on top, as the bottom hammer move forward it trips the sear holding the top hammer.

[NONOBLITUS]

Finally got the left feed open class body so I can run dual hoppers when the mood strikes.

205C69F1-A553-41AC-946B-1D9AC1ED67FB.jpeg

[BLachance75]

A couple of all bling no sting Duckslides at the field today.




Sent from my iPhone using Tapatalk

[Matt Drown]

Bought this in 2000, still has microline on the flip side, have assorted other bits/bodies all matching to go with it: Used to run with a 3/3.5/4oz CO2, swapped out to the 9ci + hero2...

[The Inflicted]

Backup Phantom with one of those new Bluefork Design stocks:

20230613-123813.jpg

[JeeperCreeper]

[redsquirrel]

2 great loadouts for one beautiful Phantom.

[JeeperCreeper]

Nope that's 2 Phantoms

[redsquirrel]

Ha, just as I was second guessing myself 😭

[ChuckLove]

I just put this together for Riot's upcoming pistol game.

[JeeperCreeper]

Looks like it will be fun

[pdogg77]

Is that the 6" barrel? It looks like there's enough room there with the pump. I was looking at building something similar but I didn't want to shoot myself in the hand, like I do with my PGP

[ChuckLove]

pdogg77 Yes that is a 6in barrel. I was concerned about shooting my hand but I don't think I'll have that issue because of the way I hold the pump handle. I hope!