instagram takipci satin al - instagram takipci satin al mobil odeme - takipci satin al

bahis siteleri - deneme bonusu - casino siteleri

bahis siteleri - kacak bahis - canli bahis

goldenbahis - makrobet - cepbahis

cratosslot - cratosslot giris - cratosslot

Announcement

Collapse
No announcement yet.

Pgp leaking,looking for advice

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    Pgp leaking,looking for advice

    Absolutely baffled by this one. I replaced the face seal, and bolt o ring but it's still leaking. The leak is mostly down the barrel, but occasionally seems to be near the grip. I've got a photo attached of the valve assembly. Any advice would be appreciated.
    Attached Files
    Feedback: https://www.mcarterbrown.com/forum/b...our-s-feedback

    #2
    Is it a PPS face seal?

    I've had these leak pretty frequently out the pack ...
    Love my brass ... Love my SSR ... Hard choices ...

    XEMON's phantom double sided feed
    Keep your ATS going: Project rATS 2.0
    My Feedback

    Comment


    • Impactfour

      Impactfour

      commented
      Editing a comment
      I replaced a PPS seal with a bacci one. Both seemed to have the same subtle leak down barrel regardless of IVG position and springing. My only guess is the lack of lead seal but the sticky says that's fine. At this point it feels like I must be making some kind of oversight because I've tried everything I can think of.


      I've swapped valve pins and valve springs, messed with the main spring using the rva to both extremes. I changed out the face seal, bolt o ring, and the (F500-0) o ring near the cup seal. My best guess is that I've got the wrong size o ring in the (68AT-035) o ring spot nearest the threaded portion of the valve.

    #3
    What does the cup seal on the valve stem look like?

    Comment


    • Impactfour

      Impactfour

      commented
      Editing a comment
      I swapped in a Crosman 22XX Valve Stem Pin as neither the stock nor dyna valve pin were piercing the 12ies enough. There doesn't seem to be any damage on either the dyna valve or crosman cup seal. I can get closer/better photos if there something particular I should be looking for.

    • AnarchicArctic

      AnarchicArctic

      commented
      Editing a comment
      You can trouble shoot poor piercing with a softer valve spring. Anything that fits really. I’ve used Spyder and phantom.

    • Impactfour

      Impactfour

      commented
      Editing a comment
      I swapped the previously not well piercing valve pin in with a phantom valve spring that felt softer and it seemed to solve the problem.

    #4
    The 2 orings on the assembly are supposed to be 012 and 014. It's likely leaking at the oring by the valve stem. As for the lead seal, that portion of valve is not under pressure, unless in the firing state where the air passes through and out the port. It has a brass nut on fine brass threads and is enough to seal that portion of the assembly.
    💀Team Ragnastock💀
    Ion Long Rifle
    Spyder Pump
    BST Feedback
    Brass Thread

    WTB Sheridan Parts

    Comment


      #5
      I've had issues with new/hard seal sealing properly ...
      the valve orings are pretty forgiving.

      Does it still leak if you remove the hammer and spring?

      Dunking the body in a tub of water can help precisely locate the leaks
      Love my brass ... Love my SSR ... Hard choices ...

      XEMON's phantom double sided feed
      Keep your ATS going: Project rATS 2.0
      My Feedback

      Comment


      • Impactfour

        Impactfour

        commented
        Editing a comment
        I just tested and it does. Right off the bat once I pierce the 12gram it starts leaking

      #6
      Does it leak both cocked and uncocked?

      Comment


      • Impactfour

        Impactfour

        commented
        Editing a comment
        Yup. Instantly leaks no matter what once the 12 gram is pierced.

      #7
      if you are around tomorrow, I can take a look at it for you.

      Comment


      • Impactfour

        Impactfour

        commented
        Editing a comment
        I think I just 'figured' it out, I don't have a Chrono put it's plenty loud when it shoots and doesn't hiss otherwise. It seems like it was a pin issue. I'll explain more below. I very much appreciate the offer though!

      #8
      So I said screw it and went against my instincts and used the only pin I hadn't tried, the stock one. Previously I'd had issues with it barely piercing 12 grams and leading to inconsistent performance. Sure enough it's shooting and not leaking now, but the 12ies seemed to be barely pierced. I'll have to see how well it chronos now next weekend. I'll attatched photos, the cold looking 12ies are with the newest pin, the frostless ones are the leaky larger piercing ones from earlier.
      Attached Files
      Feedback: https://www.mcarterbrown.com/forum/b...our-s-feedback

      Comment


      • AnarchicArctic

        AnarchicArctic

        commented
        Editing a comment
        Change that spring to get a deeper pierce

      • Impactfour

        Impactfour

        commented
        Editing a comment
        I've currently got a silver phantom valve spring, would the softer spring be a good replacement or is there another recommendation you might give? The one that came with the marker has lost most of its tension and is all but useless.

      #9
      Here's a tip for you as well.... Ditch the face seal and replace it with a Phantom cupseal,they are roughly the same size, they work great and last longer. That's all I use now.

      Comment


      • Impactfour

        Impactfour

        commented
        Editing a comment
        I'll go ahead and order some this afternoon. Bacci took weeks to deliver

      • Chuck E Ducky

        Chuck E Ducky

        commented
        Editing a comment
        Interesting never thought to try that.
    Working...
    X