Anyone have a source for macro elbows?

[Trbo323]

My stash of elbows is empty. Wondering if anyone knows the measurements for them or a good place to buy about 5-10 at a time

Is it, 1/8npt threads with a 1/4" push connect?

Sent from my Moto Z (2) using Tapatalk

[BenoitOWN]

https://airsoldier.com/product/norgr...line-fittings/

[scottieb]

I'll check what I've got. Must they all be matching?

[Trbo323]

I'll check what I've got. Must they all be matching?

No, it would be nice if at least a few of them match if I have a project that requires 2 but yeah it's not a necessity

Sent from my Moto Z (2) using Tapatalk

[Trbo323]

https://www.pneumaticplus.com/metal-...%201/8%2010-32

Would these work?

I've also come across some that the macro side is just a little too small for most macro, anyone know how to avoid these in the future or what the problem was?

Sent from my Moto Z (2) using Tapatalk

[Cdn_Cuda]

I’m in the same boat. Not a lot of Canadian paintball places are selling 90s, just straight fittings. At $10 per fitting though, it’s pricey and shipping is on top. Right now I have a stalled cocker project because I need a 90 and I want to have a couple spares in the toolbox.

[BenoitOWN]

https://www.ebay.ca/itm/MACROLINE-MA...sAAOSwwxRevgNZ

[nobbie333]

https://www.aliexpress.com/item/3229...31c13343W6AJfd

[Trbo323]

https://www.aliexpress.com/item/3229...31c13343W6AJfd

You might be on to something here, $21 for 8 fittings shipped

Have you used these before?

Sent from my Moto Z (2) using Tapatalk

[nobbie333]

I have not tried them but they look like the ones you now get from ans

[Flounder]

You can always go fancy..... https://store.chipleymachine.com/air-fittings/

[BrickHaus]

Nummech fittings are also cool.

[Trbo323]

You can always go fancy..... https://store.chipleymachine.com/air-fittings/

I mean for my own personal stuff sure, but for a Spyder that I'm fixing up so I can sell, $35 a pair is over half the money I can sell it for once I'm done

Sent from my Moto Z (2) using Tapatalk

[nobbie333]

Fancy and cheaper
http://www.nummech.com/prod_item_ptcmacroswivel.html

[lew]

McMaster Carr.

[Cunha]

You might be on to something here, $21 for 8 fittings shipped

Have you used these before?

Sent from my Moto Z (2) using Tapatalk

They look like camozzi fittings which suck. Don't get them. I promise. Hard work to make the macro seat and then chews up the hose quite a bit. Harder edges and uglier.

Get Norgren fittings for 5 dollars or whatever each. They are the best. From airsoldier or anywhere.

[Cunha]

https://airsoldier.com/product/norgr...line-fittings/

I don't see a combo pack on there unfortunately. Most places want like 11 dollars a fitting so this is a lot cheaper. It sucks there isn't a combo pack because sometimes you really do want 1 or the other type of fitting. Overall if you could only have 1 fitting type though, the swivel 90 is the best.

I love when I can use a fixed 90 though and have something dead nuts where I want it and it all works out, but usually the swivel feature makes it a lot easier to take the line on and off and such.

Is there really no one selling norgren fittings for less than a rip off per each?

Hmm here 5 dollars each maybe see what shipping adds up to http://www.macrolineguy.com/categori...oline-Fittings

[Cunha]

Going to go ahead and triple post here. I would consider ANSGEAR https://www.ansgear.com/32_Degrees_M...crolinekit.htm

They also have individual parts you can bundle with another order to get free shipping which might work for you https://www.ansgear.com/SearchResult...oline&submit=+