instagram takipci satin al - instagram takipci satin al mobil odeme - takipci satin al

bahis siteleri - deneme bonusu - casino siteleri

bahis siteleri - kacak bahis - canli bahis

goldenbahis - makrobet - cepbahis

cratosslot - cratosslot giris - cratosslot

Announcement

Collapse
No announcement yet.

WTB inception & Ti pump arm for halfblock

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    WTB inception & Ti pump arm for halfblock

    Looking for the following parts. Post here and message me with what you have please.

    Raw Inception EZ ASA
    Titanium pump arm for halfblock cocker

    Inception ram rebuild kit

    Raw nummech no-rise feedneck empire cut

    (2) raw nummech straight fittings

    Raw nummech custom series detent


    #2
    Just a suggestion don’t use the Nummech feed neck mine became a paperweight because the amount of tension needed to tighten it down so I that it won’t rotate far exceeds it’s structural integrity. It’s very thin and frail, (It’s garbage). I’m buying an Inception FLE one instead. I suggest you choose a different feed neck. I went with Nummech myself because I wanted to match my frame and it looked cool. Im sorry I did.

    Comment


      #3
      Originally posted by Chuck E Ducky View Post
      Just a suggestion don’t use the Nummech feed neck mine became a paperweight because the amount of tension needed to tighten it down so I that it won’t rotate far exceeds it’s structural integrity. It’s very thin and frail, (It’s garbage). I’m buying an Inception FLE one instead. I suggest you choose a different feed neck. I went with Nummech myself because I wanted to match my frame and it looked cool. Im sorry I did.
      Did it actually end up breaking for you? I finger tighten mine. I go pretty hard with my finger torquing. It hasn't given me any issues and is holding the hopper fine. I haven't taken any dives with it really yet though.

      Is an eclipse gtek/LV/ CS feedneck shorter than the inception ones? I thought they were kids bulky. A big appeal for me on the nummech no-rise necks is that they're so short. I like maintaining a short profile to reduce the amount of hopper hits I get.

      Comment


        #4
        Oh yeah it cracked right at the mount screw. Look how thin the material is. It’s less than a 1/16 thick. I took the clamp lever off it just incase I could use the lever on something else and threw it away.
        Attached Files

        Comment


          #5
          The FLE ones are much nicer and better built I have had one on my emek and i beat the breaks off that thing. It’s survived some pretty gnarly flops. The Nummech didn’t survive its first install.
          Last edited by Chuck E Ducky; 03-11-2024, 11:41 PM.

          Comment


            #6
            Originally posted by Chuck E Ducky View Post
            The FLE ones are much nicer and better built I have had one on my emek and i beat the breaks off that thing. It’s survived some pretty gnarly flops. The Nummech didn’t survive its first install.
            FLE? Do he eclipse ones mount on empire standard feedneck stubs? I'm thinking about getting one for a new model eclipse gun like I linked above.

            Comment


            • superman

              superman

              commented
              Editing a comment
              They have different groove locations and not all of the PE feednecks are flat on the bottom. Which would make them sit higher.

            #7


            Attached Files

            Comment


            • Schroeder
              Schroeder commented
              Editing a comment
              Do spires fit in them or are they loose? I see u have a rotor in the FLE in that pic.

            • Chuck E Ducky

              Chuck E Ducky

              commented
              Editing a comment
              Spires fit fine I have run them a few times on my emek. My wife runs a JoLo on hers.

            #8
            Thanks for all the input. I was looking over the nummech site, and it should be noted that your broken feedneck is V1. The markings on the bottom are how this can be determined. Nummech made. A revision after that. The boss-clamping screw was changed to 4-40 to prevent the issue you've shown here by thickening that material.

            Comment


            • Chuck E Ducky

              Chuck E Ducky

              commented
              Editing a comment
              That was ordered 6 months ago so it must have been recent.
          Working...
          X