WTB inception & Ti pump arm for halfblock

[Schroeder]

Looking for the following parts. Post here and message me with what you have please.

Raw Inception EZ ASA
Titanium pump arm for halfblock cocker

Inception ram rebuild kit

Raw nummech no-rise feedneck empire cut

(2) raw nummech straight fittings

Raw nummech custom series detent

[Chuck E Ducky]

Just a suggestion don’t use the Nummech feed neck mine became a paperweight because the amount of tension needed to tighten it down so I that it won’t rotate far exceeds it’s structural integrity. It’s very thin and frail, (It’s garbage). I’m buying an Inception FLE one instead. I suggest you choose a different feed neck. I went with Nummech myself because I wanted to match my frame and it looked cool. Im sorry I did.

[Schroeder]

Just a suggestion don’t use the Nummech feed neck mine became a paperweight because the amount of tension needed to tighten it down so I that it won’t rotate far exceeds it’s structural integrity. It’s very thin and frail, (It’s garbage). I’m buying an Inception FLE one instead. I suggest you choose a different feed neck. I went with Nummech myself because I wanted to match my frame and it looked cool. Im sorry I did.

Did it actually end up breaking for you? I finger tighten mine. I go pretty hard with my finger torquing. It hasn't given me any issues and is holding the hopper fine. I haven't taken any dives with it really yet though.

Is an eclipse gtek/LV/ CS feedneck shorter than the inception ones? I thought they were kids bulky. A big appeal for me on the nummech no-rise necks is that they're so short. I like maintaining a short profile to reduce the amount of hopper hits I get.

https://www.ebay.com/itm/325113889446?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=1QqjEC_ITSa&sssrc=4429486&ssuid=aRooBi7qQva&var=&widget_ver=artemis&media=COPY

[Chuck E Ducky]

Oh yeah it cracked right at the mount screw. Look how thin the material is. It’s less than a 1/16 thick. I took the clamp lever off it just incase I could use the lever on something else and threw it away.

[Chuck E Ducky]

The FLE ones are much nicer and better built I have had one on my emek and i beat the breaks off that thing. It’s survived some pretty gnarly flops. The Nummech didn’t survive its first install.

[Schroeder]

The FLE ones are much nicer and better built I have had one on my emek and i beat the breaks off that thing. It’s survived some pretty gnarly flops. The Nummech didn’t survive its first install.

FLE? Do he eclipse ones mount on empire standard feedneck stubs? I'm thinking about getting one for a new model eclipse gun like I linked above.

[superman]

They have different groove locations and not all of the PE feednecks are flat on the bottom. Which would make them sit higher.

[Chuck E Ducky]

https://www.inceptiondesigns.com/ProductDetails.asp?ProductCode=CGP-0023-MB-NA

[Schroeder]

Do spires fit in them or are they loose? I see u have a rotor in the FLE in that pic.

[Chuck E Ducky]

Spires fit fine I have run them a few times on my emek. My wife runs a JoLo on hers.

[Schroeder]

Thanks for all the input. I was looking over the nummech site, and it should be noted that your broken feedneck is V1. The markings on the bottom are how this can be determined. Nummech made. A revision after that. The boss-clamping screw was changed to 4-40 to prevent the issue you've shown here by thickening that material.

[Chuck E Ducky]

That was ordered 6 months ago so it must have been recent.