So I have a nice project body and guts. It needs a knockout finish.
Anyone doing an Aurora type finish?
Anyone doing an Aurora type finish?
-
-
As far as I know, the only ones I have seen have been very limited runs done by PbGateway. They had a Phantom and some cockers done. But one off jobs, no. There are HORROR stories of guys who tried to get it done through car parts companies, sending overseas, etc. Its a very risky and non-tolerant process. Like trying to forge swords with lava as your heat source. In almost every case the tolerances go completely off the rails and your gun might end up as a VERY expensive paperweight.
I personally love the finish. Can't ever justify the cost of the Nexus cockers that have it ($5k+), but I do love it. Getting a sick anodizing job is likely your best bet, reach out to Caustic Customs or Aesthetic Anodizing and I'm sure you could get something amazing done. -
It is funny you ask I just was looking into getting some done in a similar finish and found out the problems and price
First all the parts had to be chrome than there was a issue with timing and the minimum price was 500.00
https://westcoastpvd.com/portfolios/pvd-black-rainbow/Comment
-
I'd love to know more about how this process is done. Non-tolerant process would suggest to me that the coating/plating doesn't apply uniformly? Is the finish an anodize or is it a metal plating?Comment
-
Yes. But.... It's very expensive, long turn around time, and high failure rate.Comment
-
Neostar I think is the only one who's done paintball parts recently.Comment
-
Woof.Look up vapor deposition coatings. Quite a bit of info there.Comment
-
I think forging swords in lava is better idea. Whatever lava temperature is it is SURE to make the item only destroyable in the same exact lava pit (if you simultaneously imbue it with adequate malice)
Best of luck!Comment
-
It would be easier if the part is made of steelComment
-
Do you remember the $10k Phantom? Just to give you an idea on price to get parts done. When I looked into it one of the few that offers the process said it would be $8k upfront and couldn’t guarantee the parts would not be scrap when he was done. Knowing this it’s not a process I would ever want done. Want the look send it out for a real nice Ano you can get 90% of the look without the scrap parts and 1/4 the price. I think caustic customs did a really nice Aurora look marker a few years ago.Comment
-
You could just spray paint it rainbow. 1 of 1 custom paint job, thats always a huge value adder XDComment
-
On a related note to both this and the discussion,
Rust-oleum makes a "color shift" paint that will change colors depending on the angle of light hitting it. It's expensive, $25 a can range but turns out really nice if you have the patience to do it right
Sent from my Moto Z (2) using Tapatalk
I use Tapatalk which does NOT display comments. If you want me to see it, make it a post not a comment.
Feedback
https://www.mcarterbrown.com/forum/b...323-s-feedbackComment
-
I thought this was the place Eclipse used back in the day, and they appear to still be around.
http://neochromeparts.com/Comment
-
Owner of AG Paintball won this. It was plated by someone else. It’s perfect to. Ballsy if you think about how much theses are worth without the finish work. Probably my favorite one I have seen done.Comment
-
I remember back when ChromaFlair was about $1000 for a can of acrylic paint, typically used on high end cars. Now you can get "colorshift" at Homedepot for $25 a can, or craft stores carry similar stuff for $10 for a small bottle. None work nearly as well as ChromaFlair, and to be honest, I'm not sure how well a paintjob will hold up on a paintgun.Rust-oleum makes a "color shift" paint that will change colors depending on the angle of light hitting it. It's expensive, $25 a can range but turns out really nice if you have the patience to do it right
Seems like the kind of thing that would wear off and look terrible after a while, then you would have the challedge of removing all the acrylics
Comment
Comment