Loose Autotrigger Cam

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • commandercup
    Newbie
    • Oct 2026
    • 18

    #1

    Loose Autotrigger Cam

    Hey all,

    My autotrigger cam is sort of wiggly/loose and jiggles in place if you push it. How "firm" or "solid" are these supposed to be? I've tried fiddling with the undertravel screw too but it hasn't made much difference.

    I've been troubleshooting some other small issues, but I think it's mostly a non-issue and I just want to make sure it doesn't develop into one. I think in some rare cases I've noticed that the cam will rotate out of its normal position and I won't be able to pull the trigger even when the pump handle is forward.

    Any tips/pointers is appreciated! I think I've watched literally every single one of TF's CCM videos (thank you!) at this point haha.
    Last edited by commandercup; Yesterday, 11:21 PM.
  • Chuck E Ducky
    Ragnastock Enforcer
    • Jul 2020
    • 6368
    • NY

    #2
    Post some pictures of what you have. It depends on your setup (frame, AT cam / arm , and Pump rod)

    How long was the A/T cam retention pin missing? Is it possible it damaged the area it sits in causing excessive slop. Are you using a Delrin trigger under extreme conditions they can wear out? Possibly faster if your AT cam was fighting the mechanics of the entire process. I have never wore one out but I dont really lean on A/T all that much. But I have seen it on older more ruff played markers.

    Make sure your marker fires 1/8'' before the bolt is fully forward. (Timed properly)

    Comment

    • JohnB
      Pump, pump, pump it up
      • Jul 2020
      • 353
      • Phx

      #3
      I agree with photos and knowing what parts in particular. I feel like my 6.5 is pretty solid and doesn’t move too much. I have some cocker top and ccm lowers built up and one of them just holds in by the screw in the pump arm, so that one is pretty jiggly.

      Comment

      • Chuck E Ducky
        Ragnastock Enforcer
        • Jul 2020
        • 6368
        • NY

        #4
        Yeah the ones that are held in by a shoulder screw are definitely more sloppy however it don’t effect things unless the pump arm isn’t aligned properly. That’s why I’m curious what version he’s talking about.

        Comment

        • commandercup
          Newbie
          • Oct 2026
          • 18

          #5
          Thanks all. I uploaded some pictures and a short video of the wiggling here: https://imgur.com/a/UGWsPVS. In the process of taking it apart for photos, I realized I misspoke--the autotrigger pin was always there (I was missing the sear pin before, which was causing a different issue that has since resolved).

          When I inspected the trigger and sear, I didn't see any significant wear--definitely nothing worthy of pointing out or replacing (at least to my untrained eyes). Maybe this is just "normal" wear from using the AT a lot?

          It looks to me like the cam is able to shift in and out of the grip frame, which is the wiggling I'm seeing. I can pull on the cam while it's installed and there's a visible gap between the cam and the frame.

          Comment

          • Hellion360
            Power Lurker
            • Jul 2020
            • 2503

            #6
            That video isn't working for me.
            But that sounds like the older style of AT without the retention pin in the frame.

            The lower stop/forward travel screw helps, But I also put a small brass washer underneath the shoulder screw. It sits between the shoulder screw and the auto-trigger lever. That helps hold the lever closer to the body. I don't believe I have had a bind up on my S6 since I added that.

            The washer was one I had for shimming hinge triggers and I don't have the size available.
            Need Inception Designs or Shocktech Products? Let me know!

            MCB Feedback --------- MCB Consolidated WTB

            old PBN feedback

            Comment

            • commandercup
              Newbie
              • Oct 2026
              • 18

              #7
              I believe mine is the retaining pin version (the small pin that goes in the top of the grip frame to stop the A/T cam from falling out). My pump has an A/T pin, not a screw (although I guess I could I also use a screw?).

              I fiddled with it a little more this morning and I realize now the trigger release problem I mentioned in my OP. If I pull the cam out as far as it goes or if I tilt the marker to the left, I think it's shifting the cam out of place and blocking the trigger pull. I guess I could theoretically shim the cam on the inside of the grip frame assuming I can figure out a way to avoid any binding to keep it closer to the body.

              Comment


              • JohnB
                JohnB commented
                Editing a comment
                Yeah; those shouldn’t really move that much. You sure the retaining pin is catching on what it needs to?

              • commandercup
                commandercup commented
                Editing a comment
                Good question--I'll check after work. For what it's worth, I tried replacing the used retaining pin with a brand new one from CCM but it didn't make any difference (although it filled up the hole better and seems to sit more securely).

              • JohnB
                JohnB commented
                Editing a comment
                I don’t think the width of the pin makes a huge difference; I know people that cut a paper clip and use that and it is a good amount skinnier than an oem pin. Also make sure the frame is seated all the way forward and not sliding back on you. Something isn’t right though based on how you are describing it.
            • JohnB
              Pump, pump, pump it up
              • Jul 2020
              • 353
              • Phx

              #8
              Link doesn’t work for me too. The shim thing is a good idea if it bugs you. I think people were shimming ETHA 2 triggers with rc car shims that were 1 or 2 mm. That could work to take some slop out.

              Comment

              • commandercup
                Newbie
                • Oct 2026
                • 18

                #9
                I was able to upload a short video directly here. Hopefully this works.
                Attached Files

                Comment

                • JohnB
                  Pump, pump, pump it up
                  • Jul 2020
                  • 353
                  • Phx

                  #10
                  That looks like a normal at. The pin should rest in the groove between the rounded end and the flatish part that goes into the marker and prevent the slop you are talking about. Shouldn’t be any issues there. Not certain what is flaking off above the trigger frame though, what’s that?

                  Comment

                  • JohnB
                    Pump, pump, pump it up
                    • Jul 2020
                    • 353
                    • Phx

                    #11
                    That shifting in the video isn’t really normal though, mine moves like a half a mm or not much there. Could just be the slot for the cam has gotten bigger over the years or the pin isn’t resting in it right.

                    Comment

                    • JohnB
                      Pump, pump, pump it up
                      • Jul 2020
                      • 353
                      • Phx

                      #12
                      I am less concerned with the rattle you made ; if it works and does that no big deal. It’s the leaning left and having it fall from place and not shoot that is the issue and the two may be correlated or maybe not. I think making sure the pin slides into the right spot is the best bet. Can you wiggle it like that with the frame off holding the pin where it should be by hand?

                      Comment

                      Working...